Welcome Guest! To enable all features please Login or Register.

Notification

Icon
Error

Login


Take the time to read our Privacy Policy.

holden05 Offline
#1 Posted : Saturday, 16 December 2023 4:13:42 PM(UTC)
holden05

Rank: Member

Reputation:

Groups: Registered
Joined: 23/04/2011(UTC)
Posts: 139

Thanks: 1 times
Was thanked: 2 time(s) in 2 post(s)
I’m going to install courtesy lights in the footwell of the wb ute
I’ve come across 2 unused wires behind the kickpanel
One orange and a piggybacked pink wire
Does anyone know if these are for the courtesy lights?
Can post a pic if needed
Sandaro Offline
#2 Posted : Sunday, 17 December 2023 9:08:15 AM(UTC)
Sandaro

Rank: Member

Reputation:

Groups: Registered
Joined: 3/10/2015(UTC)
Posts: 317

Thanks: 3 times
Was thanked: 35 time(s) in 34 post(s)
Does your ute have the door jam switches to turn on the interior light? I don't know WB, but earlier models used orange and white in and out of the switch.

So probably the orange one is your choice but you should see if it leads up to the back of the door jam switch to confirm
holden05 Offline
#3 Posted : Tuesday, 19 December 2023 9:23:20 AM(UTC)
holden05

Rank: Member

Reputation:

Groups: Registered
Joined: 23/04/2011(UTC)
Posts: 139

Thanks: 1 times
Was thanked: 2 time(s) in 2 post(s)
the ute uses door jamb switches. any idea where the rear harness plugs in? is it under the dash or behind the drivers kick panel. im thinking i may be able to pick up the courtesy wiring there
HK1837 Offline
#4 Posted : Tuesday, 19 December 2023 12:39:46 PM(UTC)
HK1837

Rank: Veteran

Reputation:

Groups: Moderator, Registered, Veteran
Joined: 1/03/2005(UTC)
Posts: 14,726

Thanks: 1 times
Was thanked: 513 time(s) in 489 post(s)
Those switches are just a 0V connection. It’s normally just a single wire and the plastic plunger moves forward under spring pressure where a metal ring contacts the metal body of the switch which is in contact with the body itself, thus creating a circuit. The light(s) themselves always have 12V to them, the switches just connect the 0V side to the body and then to the - terminal of the battery.
_______________________________________________________
If we all had the same (good) taste, who would buy all the Fords?
wbute Offline
#5 Posted : Tuesday, 19 December 2023 1:28:47 PM(UTC)
wbute

Rank: Veteran

Reputation:

Groups: Registered
Joined: 25/01/2010(UTC)
Posts: 1,125

Thanks: 1 times
Was thanked: 18 time(s) in 17 post(s)
I don’t think the courtesy light wiring is there in a WB Ute. I just wired the kick panel lights out of Statesman in mine as HK suggested. They must have used a complete different harness in the Statesman to Ute.
Dr Terry Offline
#6 Posted : Tuesday, 19 December 2023 3:12:15 PM(UTC)
Dr Terry

Rank: Veteran

Reputation:

Groups: Moderator, Registered
Joined: 1/03/2005(UTC)
Posts: 6,063

Thanks: 1 times
Was thanked: 203 time(s) in 184 post(s)
Yes, the WB Statesman harness is completely different to the WB Commercial one. The WB Commercial harness is closer to HX/HZ.

The orange & white wires go up inside the A-pillar to the dome light. Orange = 12V, white = 0V. The white wire is earthed out (sorry Byron) by the headlight switch, to switch it on.

AFAIK base models (non-Kingswood) didn't get the white wires to the door switches. They can easily be added though, just run a new white wire from the RH switch to the LH one & join it to the white wire at the headlight switch. Job done.

Dr Terry
If at first you don't succeed, just call it Version 1.0
holden05 Offline
#7 Posted : Tuesday, 19 December 2023 3:25:46 PM(UTC)
holden05

Rank: Member

Reputation:

Groups: Registered
Joined: 23/04/2011(UTC)
Posts: 139

Thanks: 1 times
Was thanked: 2 time(s) in 2 post(s)
Hey Terry,
i was just going to pick up the orange and the white off the headlight switch. run them to the drivers side light with a double spade terminal then across to the pass side. this sound ok?
Dr Terry Offline
#8 Posted : Tuesday, 19 December 2023 3:32:05 PM(UTC)
Dr Terry

Rank: Veteran

Reputation:

Groups: Moderator, Registered
Joined: 1/03/2005(UTC)
Posts: 6,063

Thanks: 1 times
Was thanked: 203 time(s) in 184 post(s)
Yeah, that's fine, but what about adding the door switch wiring ?

Dr Terry
If at first you don't succeed, just call it Version 1.0
holden05 Offline
#9 Posted : Tuesday, 19 December 2023 6:14:23 PM(UTC)
holden05

Rank: Member

Reputation:

Groups: Registered
Joined: 23/04/2011(UTC)
Posts: 139

Thanks: 1 times
Was thanked: 2 time(s) in 2 post(s)
Am I better of picking the orange and white cable on the way to the dome light?
If so where wouldn’t the best place to do it?
Dr Terry Offline
#10 Posted : Wednesday, 20 December 2023 8:39:56 AM(UTC)
Dr Terry

Rank: Veteran

Reputation:

Groups: Moderator, Registered
Joined: 1/03/2005(UTC)
Posts: 6,063

Thanks: 1 times
Was thanked: 203 time(s) in 184 post(s)
As I said, the easy way to do the door switch wiring is to just run a single white wire to each switch & then connect them to the white wire at the headlight switch or some other convenient location.

Dr Terry
If at first you don't succeed, just call it Version 1.0
Users browsing this topic
Guest (2)
Forum Jump  
You cannot post new topics in this forum.
You cannot reply to topics in this forum.
You cannot delete your posts in this forum.
You cannot edit your posts in this forum.
You cannot create polls in this forum.
You cannot vote in polls in this forum.

Powered by YAF | YAF © 2003-2024, Yet Another Forum.NET
This page was generated in 0.038 seconds.