Welcome Guest! To enable all features please Login or Register.

Notification

Icon
Error

Login


Take the time to read our Privacy Policy.
HZ clutch cable adjustment
Options Go to last post Go to first unread
Previous Topic Next Topic
Guest
#1 Posted : Saturday, 2 July 2005 4:42:24 AM(UTC)
Guest

Rank: Guest

Groups: Guests
Joined: 2/09/2015(UTC)
Posts: 43,977

Was thanked: 5 time(s) in 5 post(s)
hi guys
the clutch on my HZ Kingswood van (202 and 3 on the tree!) is like a truck clutch and take up is pretty much as soon as the pedal is off the floor ... is this normal? will a pedal height and fork adjustment cure the take up and heaviness? i've drien a mate's HQ 202 ute and the pedal is a heck of a lot lighter ...
cheers frank
Back to top
Jim Briar Hill Offline
#2 Posted : Saturday, 2 July 2005 5:32:05 AM(UTC)
Jim Briar Hill

Rank: Member

Reputation:

Groups: Registered
Joined: 11/03/2005(UTC)
Posts: 96
Sounds to me that your cable is about to go bang, ( worn out ) under the drivers side you will find the adgustment screw you will need two 9/16 open enders and you need to screw it out. You might not get much out of it if it is already hard to push. Had a
Back to top
HK1837 Offline
#3 Posted : Saturday, 2 July 2005 7:46:29 AM(UTC)
HK1837

Rank: Veteran

Reputation:

Groups: Moderator, Registered, Veteran
Joined: 1/03/2005(UTC)
Posts: 14,738

Thanks: 1 times
Was thanked: 515 time(s) in 491 post(s)
Is it a half cable and half rat trap (push type clutch fork) or a full cable (pull type clutch fork)?
_______________________________________________________
If we all had the same (good) taste, who would buy all the Fords?
Back to top
crowe Offline
#4 Posted : Saturday, 2 July 2005 8:50:26 AM(UTC)
crowe

Rank: Member

Reputation:

Groups: Registered
Joined: 3/03/2005(UTC)
Posts: 287
Australia
Good topic. My HZ Sandman has the pull fork (better than linkage) I modify it. The problem is even when you are not using the clutch the weight of the pedal and the pedal pivot spring always leaves the bearing touching the preasure plate fingers. We all
Back to top
RussVRute Offline
#5 Posted : Saturday, 2 July 2005 9:24:15 PM(UTC)
RussVRute

Rank: Member

Reputation:

Groups: Registered
Joined: 23/03/2005(UTC)
Posts: 279
G'day Frank,
You would be surprised how much heavier a clutch is when the cable is worn, I replaced mine recently and it when I tried the new one out it felt like I had put a power clutch in because I was so used to how it was before, and wish I had done
Back to top
Guest
#6 Posted : Tuesday, 5 July 2005 12:41:22 AM(UTC)
Guest

Rank: Guest

Groups: Guests
Joined: 2/09/2015(UTC)
Posts: 43,977

Was thanked: 5 time(s) in 5 post(s)
hi guys

thanks heaps for the info - its an early HZ (October '77 - I guess they don't come much earlier than that!), so Byron, I guess its the half an' half ... but I will replace the cable ... any other tricks I should know?

oh and another query
Back to top
ozjason Offline
#7 Posted : Tuesday, 5 July 2005 2:25:36 AM(UTC)
ozjason

Rank: Member

Reputation:

Groups: Registered
Joined: 29/06/2005(UTC)
Posts: 287
Frank, (re blue motor dizzy)

Yes, it will drop straight in, and will run, but probably a bit rough until you:

- replace the (yellow I think, or pink, can't remember) wire coming from the ignition switch to the positive terminal of the coil with anot
Back to top
ozjason Offline
#8 Posted : Tuesday, 5 July 2005 2:28:05 AM(UTC)
ozjason

Rank: Member

Reputation:

Groups: Registered
Joined: 29/06/2005(UTC)
Posts: 287
Oh yeah... you may also have an extra wire on the electronic dizzy, that the points dizzy doesn't have. This should go on the negative of the coil - where your tacho (if you have one) also attaches. Mine didn't run until I connected the extra wire.
Back to top
Intoit Offline
#9 Posted : Tuesday, 5 July 2005 5:22:49 AM(UTC)
Intoit

Rank: Member

Reputation:

Groups: Registered
Joined: 1/03/2005(UTC)
Posts: 73
While on the subject of the elect. ignition , does anyone know of a reputable company , preferably in south western Sydney who does this . My nieces boyfriend is about to drop one in their HX Monaro . He too is a bit concerned about the pinging issue and
--------------------Go Hard Or Go Home
Back to top
RussVRute Offline
#10 Posted : Tuesday, 5 July 2005 6:54:48 AM(UTC)
RussVRute

Rank: Member

Reputation:

Groups: Registered
Joined: 23/03/2005(UTC)
Posts: 279
Give a company called dizzyfix a call, the guys name is Fred, his Mobile No. is 0418 258 045, you can drop off and pick up, at his home or he can pick up and deliver, he is at Edensor Park, near liverpool, so hes not far from you, he did mine, and it cost
Back to top
Intoit Offline
#11 Posted : Tuesday, 5 July 2005 3:57:34 PM(UTC)
Intoit

Rank: Member

Reputation:

Groups: Registered
Joined: 1/03/2005(UTC)
Posts: 73
Thanks Russ , we will give him a call
--------------------Go Hard Or Go Home
Back to top
Guest
#12 Posted : Wednesday, 6 July 2005 11:59:04 PM(UTC)
Guest

Rank: Guest

Groups: Guests
Joined: 2/09/2015(UTC)
Posts: 43,977

Was thanked: 5 time(s) in 5 post(s)
Thanks guys - great to know there's a wealth of good info out there!
cheers f.
Back to top
Guest
#13 Posted : Thursday, 7 July 2005 5:26:08 AM(UTC)
Guest

Rank: Guest

Groups: Guests
Joined: 2/09/2015(UTC)
Posts: 43,977

Was thanked: 5 time(s) in 5 post(s)
.
Back to top
Users browsing this topic
Guest (2)
Forum Jump  
You cannot post new topics in this forum.
You cannot reply to topics in this forum.
You cannot delete your posts in this forum.
You cannot edit your posts in this forum.
You cannot create polls in this forum.
You cannot vote in polls in this forum.

Powered by YAF | YAF © 2003-2025, Yet Another Forum.NET
This page was generated in 0.088 seconds.