Rank: Member
Groups: Registered
Joined: 29/06/2011(UTC)
Posts: 12
|
I just bought a land rover with a 186P motor in it, when I got it there was no coil. I had 3 lying around so tried all 3 and still no spark. unless I'm unlucky and just happen to have 3 dud coils, what else could be wrong? I have tried hooking up both properly through the wiring harness and also a wire directly from the battery to the + on the coil with the negative hooked up to the one wire on the dizzy (points dizzy) and hooked a timing light up to a couple of the plugs while cranking and nothing. Any ideas? Is my hookup method correct? If I could get it running at least it will be easier to sell, but turns over nice and quietly so sounds like a good one.
|
|
|
|
|
|
Rank: Member
Groups: Registered
Joined: 23/02/2011(UTC)
Posts: 13
|
Are the points opening and closing? With ignition switch on, is there power at the positive side of the coil? Is there a spark at the points when you manually open and close them?
|
|
|
|
|
|
Rank: Veteran
Groups: Moderator, Registered
Joined: 1/03/2005(UTC)
Posts: 6,064
Thanks: 1 times
Was thanked: 203 time(s) in 184 post(s)
|
The best tool for solving this problem is a good old fashioned 12V test light. Forget multi-meters & all that other fancy stuff, a simple light will tell all.
1. See if it lights up at the coil +ve with the ignition on. If it doesn't you have a ignition switch or wiring issue.
2. If it does, then see if it lights up at the coil -ve.
3. If it does, this means that the coil is probably OK & that the points are open or they're stuffed. If it doesn't the coil is open circuit or the points are closed or you have a short (to ground) at the points wire. To test for an open circuit coil, remove the wire to the distributor (& any others) & test the -ve terminal again.
4. Try cranking the motor, the light should flash as the points open & close. If the light stays bright the points are too wide open or dirty & not contacting.
It's unlikely you have 3 stuffed coils.
Dr Terry. |
If at first you don't succeed, just call it Version 1.0 |
|
|
|
|
|
Rank: Member
Groups: Registered
Joined: 23/07/2010(UTC)
Posts: 690
Was thanked: 1 time(s) in 1 post(s)
|
quote:
Originally posted by Dr Terry
The best tool for solving this problem is a good old fashioned 12V test light. Forget multi-meters & all that other fancy stuff, a simple light will tell all.
1. See if it lights up at the coil +ve with the ignition on. If it doesn't you have a ignition switch or wiring issue.
2. If it does, then see if it lights up at the coil -ve.
3. If it does, this means that the coil is probably OK & that the points are open or they're stuffed. If it doesn't the coil is open circuit or the points are closed or you have a short (to ground) at the points wire. To test for an open circuit coil, remove the wire to the distributor (& any others) & test the -ve terminal again.
4. Try cranking the motor, the light should flash as the points open & close. If the light stays bright the points are too wide open or dirty & not contacting.
It's unlikely you have 3 stuffed coils.
Dr Terry.
try another dissy. they can be temprimental at times
|
|
|
|
|
|
Forum Jump
You cannot post new topics in this forum.
You cannot reply to topics in this forum.
You cannot delete your posts in this forum.
You cannot edit your posts in this forum.
You cannot create polls in this forum.
You cannot vote in polls in this forum.
