Welcome Guest! To enable all features please Login or Register.

Notification

Icon
Error

Login


Take the time to read our Privacy Policy.
253 ported vacuum
Options Go to last post Go to first unread
Previous Topic Next Topic
Aussie Dave Offline
#1 Posted : Wednesday, 15 March 2023 12:04:17 PM(UTC)
Aussie Dave

Rank: Member

Reputation:

Groups: Registered
Joined: 15/03/2023(UTC)
Posts: 12
Australia
Location: Shepparton
Hi everyone, I am new to the forum and could use some help. My car is a HZ, manual, 253, basically standard but with a very mild cam and extractors. I am playing with distributor advance, and find that at idle the ported vacuum is showing 15" at idle. Shouldn't this be close to zero, and if so why is mine so high. Thanks for your help.
Back to top
HK1837 Offline
#2 Posted : Wednesday, 15 March 2023 5:08:12 PM(UTC)
HK1837

Rank: Veteran

Reputation:

Groups: Moderator, Registered, Veteran
Joined: 1/03/2005(UTC)
Posts: 14,717

Thanks: 1 times
Was thanked: 512 time(s) in 488 post(s)
Wrong carby possibly? Is it a proper HZ carby? One of those should have both ported and full vacuum ports. The ported vacuum port is the one used for the canister purge signal, and a manual car has a T off this for vacuum advance.
_______________________________________________________
If we all had the same (good) taste, who would buy all the Fords?
Back to top
Aussie Dave Offline
#3 Posted : Wednesday, 15 March 2023 6:48:37 PM(UTC)
Aussie Dave

Rank: Member

Reputation:

Groups: Registered
Joined: 15/03/2023(UTC)
Posts: 12
Australia
Location: Shepparton
Thanks for the reply. I believe the carb is from a HJ, it has the port in the middle of the carb at the back. This port is reading 15" basically the same as manifold vacuum. Am I correct that at idle it should be close to zero. Thanks
Back to top
HK1837 Offline
#4 Posted : Thursday, 16 March 2023 4:41:14 AM(UTC)
HK1837

Rank: Veteran

Reputation:

Groups: Moderator, Registered, Veteran
Joined: 1/03/2005(UTC)
Posts: 14,717

Thanks: 1 times
Was thanked: 512 time(s) in 488 post(s)
It must be an auto carby so it isn’t ported vacuum.
_______________________________________________________
If we all had the same (good) taste, who would buy all the Fords?
Back to top
Aussie Dave Offline
#5 Posted : Thursday, 16 March 2023 5:59:02 AM(UTC)
Aussie Dave

Rank: Member

Reputation:

Groups: Registered
Joined: 15/03/2023(UTC)
Posts: 12
Australia
Location: Shepparton
Thanks for the suggestion, I will see if I can find a part number and check.
Back to top
Aussie Dave Offline
#6 Posted : Thursday, 16 March 2023 4:46:32 PM(UTC)
Aussie Dave

Rank: Member

Reputation:

Groups: Registered
Joined: 15/03/2023(UTC)
Posts: 12
Australia
Location: Shepparton
I checked the number on the carby, they are 233085 with 55 on a separate line. These number don't line up with my HZ Parts Catalogue, but as I said in the first post I think the engine might be HJ. The numbers do end in 5 so I am guessing it a manual Carby. What are your thoughts. Regards
Back to top
HK1837 Offline
#7 Posted : Thursday, 16 March 2023 5:56:56 PM(UTC)
HK1837

Rank: Veteran

Reputation:

Groups: Moderator, Registered, Veteran
Joined: 1/03/2005(UTC)
Posts: 14,717

Thanks: 1 times
Was thanked: 512 time(s) in 488 post(s)
I'm pretty sure 23-3085 is the HJ and LH pre-canister carby. 23-3086 is the manual version.

The distributor vacuum port on the manual carb is above the PCV port from memory, and on the auto carb it is to the left on it looking from the distributor.

The later HX-HZ style carby has 4 ports on the dizzy side: PCV (big one), ported vacuum above it (same as on earlier manual carby), a little full vacuum port to the left of the PCV port for the air cleaner and a canister purge port above the air cleaner port (also used for ported vacuum to the distributor via the pollution equipment).
_______________________________________________________
If we all had the same (good) taste, who would buy all the Fords?
Back to top
Aussie Dave Offline
#8 Posted : Thursday, 16 March 2023 6:02:45 PM(UTC)
Aussie Dave

Rank: Member

Reputation:

Groups: Registered
Joined: 15/03/2023(UTC)
Posts: 12
Australia
Location: Shepparton
Thanks for your help, I will either put up with this carby, or get a manual carby, or get a quadrajet and manifold. Thanks again for your help
Back to top
HK1837 Offline
#9 Posted : Thursday, 16 March 2023 6:47:13 PM(UTC)
HK1837

Rank: Veteran

Reputation:

Groups: Moderator, Registered, Veteran
Joined: 1/03/2005(UTC)
Posts: 14,717

Thanks: 1 times
Was thanked: 512 time(s) in 488 post(s)
I’d recommend:

Blue Quadrajet. 17059596 CXL. Regularly see them at swap meets for $100 or less. $350-$375 for a full rebuild.

KC 4BBL intake. They fit all HT to VL heads. Or an Edelbrock Performer. Here is one on Gumtree. Cost about $750 new.

http://www.gumtree.com.a...cial&utm_source=sms

HEI dizzy off a blue or black 308. Cheaper to buy new nowadays with a HEI coil. Goss sell them cheap. One on EBay.

https://www.ebay.com.au/...W0%7Ctkp%3ABFBM7LnGmd1h

Pull the ignition switch and solder a wire across the run and start contacts (pink and yellow wires). Fit blue V8 plugs and gap to suit blue V8.
_______________________________________________________
If we all had the same (good) taste, who would buy all the Fords?
Back to top
Aussie Dave Offline
#10 Posted : Thursday, 16 March 2023 7:05:57 PM(UTC)
Aussie Dave

Rank: Member

Reputation:

Groups: Registered
Joined: 15/03/2023(UTC)
Posts: 12
Australia
Location: Shepparton
Thanks for the advice, I already have the HEI distributor (blue) fitted, it was playing with it, that raised this carby issue, so that parts done. I have been thinking about the Quadrajet conversion for some time so have a HZ 4 barrel manifold in stock and factory air cleaner. Just need the carby. I will have to check on my plugs and gaps. I have noted the Quadrajet number, may just buy a reconditioned one ready to go. Thanks again I appreciate your help and knowledge. All of this relates to a car ( 4 door GTS) that I purchased, so I don't know the history and anything that might need an update, all good I like explore and learn. Regards
Back to top
HK1837 Offline
#11 Posted : Thursday, 16 March 2023 7:12:54 PM(UTC)
HK1837

Rank: Veteran

Reputation:

Groups: Moderator, Registered, Veteran
Joined: 1/03/2005(UTC)
Posts: 14,717

Thanks: 1 times
Was thanked: 512 time(s) in 488 post(s)
The HZ 4 barrel intake isn’t all that great. It is better than HX though which was awful. HX has barrels down the head sides intended for water but not used. HZ is flat in that area.
The KC intake is a copy of the HDT VC-VK intake but has facility to fit all red heads too. You can buy the carbs ready to go, try Nigel at Xtreme fuel systems. Get a set of bungs too to block off unused ports. The manual vacuum port is on the front of these on the passenger side.
_______________________________________________________
If we all had the same (good) taste, who would buy all the Fords?
Back to top
Aussie Dave Offline
#12 Posted : Thursday, 16 March 2023 7:22:48 PM(UTC)
Aussie Dave

Rank: Member

Reputation:

Groups: Registered
Joined: 15/03/2023(UTC)
Posts: 12
Australia
Location: Shepparton
Great job, thanks again
Back to top
HK1837 Offline
#13 Posted : Thursday, 16 March 2023 7:31:06 PM(UTC)
HK1837

Rank: Veteran

Reputation:

Groups: Moderator, Registered, Veteran
Joined: 1/03/2005(UTC)
Posts: 14,717

Thanks: 1 times
Was thanked: 512 time(s) in 488 post(s)
_______________________________________________________
If we all had the same (good) taste, who would buy all the Fords?
Back to top
Users browsing this topic
Guest (2)
Forum Jump  
You cannot post new topics in this forum.
You cannot reply to topics in this forum.
You cannot delete your posts in this forum.
You cannot edit your posts in this forum.
You cannot create polls in this forum.
You cannot vote in polls in this forum.

Powered by YAF | YAF © 2003-2024, Yet Another Forum.NET
This page was generated in 0.077 seconds.