Rank: Member
Groups: Registered
Joined: 28/05/2016(UTC) Posts: 43 ![Australia Australia]() Location: Sydney Thanks: 8 times Was thanked: 3 time(s) in 3 post(s)
|
There are two holes in the floor pan where the drivers left foot would rest. What are they for? They can be seen in the following videos, so I know they are a common thing. Seen here: https://youtu.be/wFy76FiL8QI?t=98And here but harder to see: https://youtu.be/yk40zP5OEcA?t=300
|
|
|
|
Rank: Member
Groups: Registered
Joined: 28/05/2016(UTC) Posts: 43 ![Australia Australia]() Location: Sydney Thanks: 8 times Was thanked: 3 time(s) in 3 post(s)
|
I'll answer this one myself in case a future person is wondering the same thing. The holes are there in manufacturing and are usually filled with seam sealer or equivalent.
|
|
|
|
Rank: Member
Groups: Registered
Joined: 6/07/2019(UTC) Posts: 364 ![Australia Australia]() Location: bayside Melbourne Thanks: 225 times Was thanked: 28 time(s) in 28 post(s)
|
Originally Posted by: tidyVan ![Go to Quoted Post Go to Quoted Post](/Forum/Themes/soclean/icon_latest_reply.gif) I'll answer this one myself in case a future person is wondering the same thing. The holes are there in manufacturing and are usually filled with seam sealer or equivalent. ummm... not in my experience GMH put a small bung or blanking plate over those (and others) on the Holden series floor pans and on Commodore went for a rubber grommet on all (as seen below) ![](https://images2.imgbox.com/da/71/FD1UKye4_o.jpg) |
Club circuit racing...the best fun you can have with your pants on |
|
|
|
Rank: Member
Groups: Registered
Joined: 28/05/2016(UTC) Posts: 43 ![Australia Australia]() Location: Sydney Thanks: 8 times Was thanked: 3 time(s) in 3 post(s)
|
This is the clearest image I've been able to find. It's the two small holes on either side of the tunnel, not the large holes that would have blanking plates put over them. ![Floor pan holes Floor pan holes](https://allmusclecarparts.com.au/media/catalog/product/cache/1/image/1200x/040ec09b1e35df139433887a97daa66f/h/d/hdnfp02.8.jpg) Edited by user Wednesday, 29 May 2024 7:11:24 PM(UTC)
| Reason: Not specified
|
|
|
|
Rank: Veteran
Groups: Moderator, Registered, Veteran
Joined: 1/03/2005(UTC) Posts: 14,649
Thanks: 1 times Was thanked: 494 time(s) in 471 post(s)
|
They used to punch those through those low point channels so when the bodies in white were sitting outside waiting to enter the body plant paint area water could run out. If you look at HK-HG they are there too. Not all body plants did it though from memory, I know Pagewood did. I think they also did double duty allowing the body dip to run out when the body was dipped. |
_______________________________________________________ If we all had the same (good) taste, who would buy all the Fords? |
|
|
|
Rank: Member
Groups: Registered
Joined: 29/07/2006(UTC) Posts: 766 Location: in the shed
Thanks: 8 times Was thanked: 14 time(s) in 13 post(s)
|
Bare metal bodies went through a shower of hot water and phosphoric acid known as phosphating to etch and prep the metal. All of that had to drain out. Then onto the drier, then they were dipped and that also had to drain out.
I think mine had 8 or more holes filled with black mastic.
|
|
|
|
Forum Jump
You cannot post new topics in this forum.
You cannot reply to topics in this forum.
You cannot delete your posts in this forum.
You cannot edit your posts in this forum.
You cannot create polls in this forum.
You cannot vote in polls in this forum.