Rank: Member
Groups: Registered
Joined: 15/02/2024(UTC) Posts: 28 ![Australia]( "Australia") Location: NSW Thanks: 13 times
|
If I'm reading an old thread right, to plumb in the heater in a HZ I have to put the blocking caps onto where the short hose is between the manifold and the water pump, and put the heater hoses onto where it's currently blocked off? And if there's one present at all the heater tap will be inside under the dash somewhere? Which hose goes to the top in the firewall? Thanks in advance.  
|
|
|
|
|
|
Rank: Veteran
Groups: Registered
Joined: 25/01/2010(UTC)
Posts: 1,124
Thanks: 1 times
Was thanked: 18 time(s) in 17 post(s)
|
Heater tap definitely goes in the engine bay between thermostat housing and firewall. The cable to open it comes from the control in the dash on drivers side and hooks onto the tap.
|
 1 user thanked wbute for this useful post.
|
|
|
|
Rank: Member
Groups: Registered
Joined: 15/02/2024(UTC) Posts: 28 ![Australia]( "Australia") Location: NSW Thanks: 13 times
|
Does that mean there should be a bracket or something to hold the tap still so the cable can action it?
|
|
|
|
|
|
Rank: Veteran
Groups: Moderator, Registered, Veteran
Joined: 1/03/2005(UTC)
Posts: 14,717
Thanks: 1 times
Was thanked: 512 time(s) in 488 post(s)
|
|
_______________________________________________________
If we all had the same (good) taste, who would buy all the Fords? |
1 user thanked HK1837 for this useful post.
|
|
|
|
Rank: Veteran
Groups: Moderator, Registered
Joined: 1/03/2005(UTC)
Posts: 6,058
Thanks: 1 times
Was thanked: 203 time(s) in 184 post(s)
|
There is no heater tap on any HQ-HZ with a standard heater.
If the car has 'forced air ventilation' where the dash has 4 face level outlets then there is a tap (as pictured in the ebay advert). This tap is actuated by a cable which exits the firewall just under the heater box.
BTW, the pic of the heater block-offs & by-pass is not correct. That thermostat housing is HQ-style. The correct HX-HZ one has 2 outlets, one for the heater & one for the by-pass hose to the water pump. The by-pass hose has never gone to the front of the inlet manifold. That threaded port is for a temp sensor or vacuuum switch.
Dr Terry |
If at first you don't succeed, just call it Version 1.0 |
1 user thanked Dr Terry for this useful post.
|
|
|
|
Rank: Veteran
Groups: Registered
Joined: 25/01/2010(UTC)
Posts: 1,124
Thanks: 1 times
Was thanked: 18 time(s) in 17 post(s)
|
I thought forced air was standard on HZ?
|
|
|
|
|
|
Rank: Veteran
Groups: Moderator, Registered
Joined: 1/03/2005(UTC)
Posts: 6,058
Thanks: 1 times
Was thanked: 203 time(s) in 184 post(s)
|
Originally Posted by: wbute  I thought forced air was standard on HZ? To my knowledge it wasn't standard on base models like one-tonner, ute & van. As I said it's easy to tell. See if the extra cable is present & check the control panel, it's slightly different to standard as well. Dr Terry Edited by user Tuesday, 5 March 2024 7:19:59 AM(UTC)
| Reason: Not specified |
If at first you don't succeed, just call it Version 1.0 |
1 user thanked Dr Terry for this useful post.
|
|
|
|
Rank: Veteran
Groups: Moderator, Registered, Veteran
Joined: 1/03/2005(UTC)
Posts: 14,717
Thanks: 1 times
Was thanked: 512 time(s) in 488 post(s)
|
C57 was optional on M60/70/80 on HZ when released but became standard during HZ. Not sure exactly when but it was there by early 1979 as the Sandman package was also revised at the same time to remove C57 as a component option as it became a mandatory option on the base vehicle. |
_______________________________________________________
If we all had the same (good) taste, who would buy all the Fords? |
1 user thanked HK1837 for this useful post.
|
|
|
|
Forum Jump
You cannot post new topics in this forum.
You cannot reply to topics in this forum.
You cannot delete your posts in this forum.
You cannot edit your posts in this forum.
You cannot create polls in this forum.
You cannot vote in polls in this forum.
