Welcome Guest! To enable all features please Login or Register.

Notification

Icon
Error

Login


Take the time to read our Privacy Policy.

DJBOOBY Offline
#1 Posted : Tuesday, 29 August 2006 7:53:04 AM(UTC)
DJBOOBY

Rank: Member

Reputation:

Groups: Registered
Joined: 29/08/2006(UTC)
Posts: 3

hi need to know if there a place i can send my xf flywheel to be repaired with new ring gear as well as mechined and balance as im puting behind a worked 4.1
live nere Wagga Wagga nsw (Tumut)
Guest
#2 Posted : Friday, 1 September 2006 7:10:25 AM(UTC)
Guest

Rank: Guest

Groups: Guests
Joined: 2/09/2015(UTC)
Posts: 43,977

Was thanked: 5 time(s) in 5 post(s)
any place that does clutches should have no problem doing this sort of thing. the balancing will need to be done at the same time as the motor, as the crank rods pistons and flywheel all need to be balanced too
DJBOOBY Offline
#3 Posted : Saturday, 2 September 2006 3:39:50 AM(UTC)
DJBOOBY

Rank: Member

Reputation:

Groups: Registered
Joined: 29/08/2006(UTC)
Posts: 3

yep motor will be balance the one im getting has a full balance, race poistons, lager valves / v/springs, crow cam,crow timing chain,race bearings, race gasket set,
i know flywheel should be on when doing balance but motor was built some time back
Guest
#4 Posted : Thursday, 23 November 2006 9:42:08 PM(UTC)
Guest

Rank: Guest

Groups: Guests
Joined: 2/09/2015(UTC)
Posts: 43,977

Was thanked: 5 time(s) in 5 post(s)
take it 2 a clutch joint
Guest
#5 Posted : Thursday, 23 November 2006 11:40:40 PM(UTC)
Guest

Rank: Guest

Groups: Guests
Joined: 2/09/2015(UTC)
Posts: 43,977

Was thanked: 5 time(s) in 5 post(s)
You can replace the ring gear yourself - if you have oxy gear. Then all you need to do get it machined.
johnperth Offline
#6 Posted : Sunday, 26 November 2006 10:49:11 AM(UTC)
johnperth

Rank: Veteran

Reputation:

Groups: Registered, Veteran
Joined: 1/03/2005(UTC)
Posts: 1,991

Was thanked: 2 time(s) in 2 post(s)
You don't need oxy or anything fancy. Use a good sharp cold chisel, crack the ringgear off, helps to start with a hacksaw cut,on about 4 parts of the new ring gear polish a small area, put the new ring gear in the oven or use a blow torch or lpg torch, he
johnperth Offline
#7 Posted : Sunday, 26 November 2006 10:50:39 AM(UTC)
johnperth

Rank: Veteran

Reputation:

Groups: Registered, Veteran
Joined: 1/03/2005(UTC)
Posts: 1,991

Was thanked: 2 time(s) in 2 post(s)
Oh as misc said make sure you get it machined if it needs a new ring gear it is sure to be hollowed out, and the new clutch will not work properly.
Users browsing this topic
Guest
Forum Jump  
You cannot post new topics in this forum.
You cannot reply to topics in this forum.
You cannot delete your posts in this forum.
You cannot edit your posts in this forum.
You cannot create polls in this forum.
You cannot vote in polls in this forum.

Powered by YAF | YAF © 2003-2025, Yet Another Forum.NET
This page was generated in 0.091 seconds.