Rank: Member
Groups: Registered
Joined: 23/04/2011(UTC)
Posts: 139
Thanks: 1 times
Was thanked: 2 time(s) in 2 post(s)
|
What is the process here. Car is a v8 auto
|
|
|
|
|
|
Rank: Member
Groups: Registered
Joined: 6/07/2019(UTC) Posts: 379 ![Australia]( "Australia") Location: bayside Melbourne Thanks: 237 times
Was thanked: 28 time(s) in 28 post(s)
|
Vc commodore radiator removal? V8 auto?
remove temp sensor harness (if fitted.. some have a temp sensor for A/C in a side tank)
remove auto trans lines from side tank
remove top and bottom radiator hoses (note - bottom can be removed at pump outlet if you cannot get the clamp off the hose at the radiator).. beware coolant will go everywhere when the bottom hose is removed
remove top radiator shroud (on top rad panel) .. lever out retainers
remove overflow tube (from where it connects at the side of the top where the cap is (note cap does NOT need removing)
remove 2 side clips (sitting in front panel retainers) by pressing down and levering out
pull radiator straight up (note the side rubber vibration blocks might be a bit stuck.. just jiggle sideways if so)
done ...
|
Club circuit racing...the best fun you can have with your pants on |
|
|
|
|
|
Rank: Member
Groups: Registered
Joined: 23/04/2011(UTC)
Posts: 139
Thanks: 1 times
Was thanked: 2 time(s) in 2 post(s)
|
To get to the auto trans lines, do I remove the grill or can I get to them once I’ve removed the top panel?
|
|
|
|
|
|
Rank: Member
Groups: Registered
Joined: 6/07/2019(UTC) Posts: 379 ![Australia]( "Australia") Location: bayside Melbourne Thanks: 237 times
Was thanked: 28 time(s) in 28 post(s)
|
Originally Posted by: holden05  To get to the auto trans lines, do I remove the grill or can I get to them once I’ve removed the top panel? neither from the passenger side... look behind the headligh at the radiator, you can see the auto trans fluid pipes coming from under the car and up to the radiator they are shown here .. on the passenger side tank above the bottom hose connector  |
Club circuit racing...the best fun you can have with your pants on |
|
|
|
|
|
Rank: Member
Groups: Registered
Joined: 6/07/2019(UTC) Posts: 379 ![Australia]( "Australia") Location: bayside Melbourne Thanks: 237 times
Was thanked: 28 time(s) in 28 post(s)
|
here is an aftermarket rad for VB-VK V8s and you can see more clearly the 2 pipe connectors this one also has a temp sensor boss under the top rad hose connector on the drivers side  Edited by user Thursday, 28 December 2023 5:46:04 PM(UTC)
| Reason: Not specified |
Club circuit racing...the best fun you can have with your pants on |
|
|
|
|
|
Rank: Member
Groups: Registered
Joined: 23/04/2011(UTC)
Posts: 139
Thanks: 1 times
Was thanked: 2 time(s) in 2 post(s)
|
Ok, I’ll have to check that out. I’m not near the car at the moment but would I be right in saying that they would be more accessible once the fan shroud is removed?
|
|
|
|
|
|
Rank: Member
Groups: Registered
Joined: 6/07/2019(UTC) Posts: 379 ![Australia]( "Australia") Location: bayside Melbourne Thanks: 237 times
Was thanked: 28 time(s) in 28 post(s)
|
Originally Posted by: holden05 Ok, I’ll have to check that out. I’m not near the car at the moment but would I be right in saying that they would be more accessible once the fan shroud is removed? yes... and the shroud may/may not have to come off to get the rad out (no biggie as the factory shrouds need 2 screws undone at the top) |
Club circuit racing...the best fun you can have with your pants on |
|
|
|
|
|
Rank: Member
Groups: Registered
Joined: 23/04/2011(UTC)
Posts: 139
Thanks: 1 times
Was thanked: 2 time(s) in 2 post(s)
|
Is there a trick to getting the clips on the sides out?
|
|
|
|
|
|
Rank: Member
Groups: Registered
Joined: 6/07/2019(UTC) Posts: 379 ![Australia]( "Australia") Location: bayside Melbourne Thanks: 237 times
Was thanked: 28 time(s) in 28 post(s)
|
Originally Posted by: holden05 Is there a trick to getting the clips on the sides out? no .. not really, it is just an upside down sort of W clip but how I do it, is to depress one side (either side... ) with a screwdriver and then put another screwdriver thru the middle (the sticking up bit) of the clip and twist that will pull one end of the clip out of the retainer housing (that the rubber mount is in) and once one end is out, tilt the clip and pull the other end out Clips look like this  Edited by user Thursday, 4 January 2024 7:16:13 PM(UTC)
| Reason: Not specified |
Club circuit racing...the best fun you can have with your pants on |
|
|
|
|
|
Forum Jump
You cannot post new topics in this forum.
You cannot reply to topics in this forum.
You cannot delete your posts in this forum.
You cannot edit your posts in this forum.
You cannot create polls in this forum.
You cannot vote in polls in this forum.
